Proxel Invisible Electromagnetic Parking Sensors Front + Rear.

Description

INVISIBLE
Without drilling the bumper
MADE in Italy
Produced in Italy
The guarantee and the quality of
Made in Italy
Directly from the manufacturer
Designed and produced in Italy. FWe supply reliability since
1993
.
Without changing the aesthetics of the car
Thanks to the installation of the sensor inside the bumper, it does not affect the bumper line.
Invisible electromagnetic parking sensors kit
Front and Rear
without holes
The rear and front Electromagnetic backup sensor are completely invisible and it does not change the look of your car.
The approach the obstacle is always indicated with
three different sounds
: pre-alarm, alarm and risk of contact. The sounds of the front version are different than the back version.
The rear electronic central unit is positioned within the car near the rear lights, while the front one is placed inside the vehicle under the dashboard.
Details EPS-DUAL 4.0 (rear)
Details EPS-FRONT 4.0 (front)
Main features
EPS-DUAL 4.0
(rear)
Range
from 70/80 cm. (28/32 inches) up to a few centimeters
Obstacles detected
all shapes and materials
Sensitivity
adjustment with 4 pre-set sensitivities
Power
connection to the reversing lamp
Activation
with the insertion of the reverse gear
Antenna sensor Length
3,5 meters / 12 feet (can be cut to the length of the bumper)
Buzzer cable length
1,7 meters / 5,5 feet
Data Cable length
1,5 meters / 5 feet
Compatible with CAN BUS and CHECK CONTROL
No interference with other on-board equipments
Antenna sensor  installation
on the innner surface of the bumper
Vehicles that are not compatible
EPS-DUAL 4.0
(rear):
The following vehicles are NOT compatible with the backup sensor EPS-DUAL 4.0:
Pickup Mazda | Mitsubishi L200 | Nissan Patrol (with metal bumper) | Nissan Pathfinder (version with spare wheel on the tailgate) | Nissan Navara | Toyota Rav 4 (before 2006) | Audi A4 (2006) | Fiat Doblo (pre 2010) | Isuzu D-Max | VW T5 California | volkswagen amarok | Nissan Primastar | Jeep Cherokee (version with spare wheel on the tailgate) | Jeep Wrangler | Peugeot Partner Tepee | Mitsubishi Pajero | Mercedes ML 2002 | VW Caddy | Hyundai H1 | Suzuki Splash (2014) | Fiat Ducato | Fiat Fullback | Land Rover Discovery 2 | Land Rover Defender | Mercedes Vito | Range Rover 1999 | Renault Trafic | Toyota Hilux | Mercedes Citan | Opel Vivaro |
Precautions for the Audi A4 and Audi A6 (4f)
EPS-DUAL 4.0
(rear):
On some versions of the Audi A4 and Audi A6 (4f) you can not install the standard antenna sensor supplied with model EPS-DUAL 4.0 but you must use a specific antenna sensor (
details
). You can request this special type of antenna sensor writing on the notes before submitting the order.
Installation instructions
EPS-DUAL 4.0
(rear)
Mounting Instructions rear backup sensor mod. EPS-DUAL 4.0
Main features
EPS-FRONT 4.0
(front)
Range
from 60/70 cm. (24/28 inches) up to a few centimeters/inches
Obstacles detected
all shapes and materials
Sensitivity
adjustment with 4 pre-set sensitivities
Power
connection to the vehicle battery
Activation
by button
Antenna sensor Length
3,5 meters / 12 feet (can be cut to the length of the bumper)
Buzzer-push button cable length
1,0 meters / 3,3 feet
DATA Cable length
2,5 meters / 8,2 feet
Compatible with CAN BUS and CHECK CONTROL
No interference with other on-board equipments
Antenna sensor  installation
on the innner surface of the bumper
Vehicles that are not compatible
EPS-FRONT 4.0
(front):
The following vehicles are NOT compatible with the backup sensor EPS-FRONT 4.0:
- Jeep Wrangler
- BMW Z4 (2007)
- Land Rover Defender
- Range Rover (1999)
Installation instructions
EPS-FRONT 4.0
(front)
Mounting Instructions front parking sensor mod. EPS-FRONT 4.0
Antenna sensor
Unlike classical "button" sensors our Electromagnetic backup sensors use a single sensor that is attached to the inside surface of the bumper.
The antenna sensor is an aluminum
strip 1 cm (0,4 inch)long 3.5 meters high and thick a few tenths of a millimeter (thousandth of an inch).
Once applied from one end to the other of the bumper the excess can be cut away.
Details
Where to install the sensor antenna on your car:
We suggest the
position of the antenna sensor
in the bumper. If your car is not
listed
please report it via
e-mail
indicating the model and production year of registration.
By buying this product on our website you will be entitled to:
3 years warranty
Manufacturer's technical support
Italian product
More information
For more information and specifications go to our website:
www.proxel.com