Proxel invisible parking sensors Front + Rear Wireless Display.

Description

INVISIBLE
Without drilling the bumper
Made in Italy
Produced in Italy
The guarantee and the quality of the
Made in Italy
Directly from the manufacturer
Designed and produced in Italy. We have been providing reliability since
1993
.
Without changing the aesthetics of the car
Thanks to the installation of the sensor inside the bumper, it does not affect the line of the bumper.
Proxel invisible electromagnetic parking sensors
Front + Rear with Wireless Display
The electromagnetic rear and front parking sensors are completely invisible and do not change the aesthetics of your car.
For the rear version, the approach of the obstacle is signaled by a sequential increase of “BEEP” which becomes more and more frequent as the vehicle approaches the obstacle. For the earlier version the approach of the obstacle is always signaled with three different sounds: pre-alarm, alert and risk of contact.
The electronic control unit for the rear version is located inside the luggage compartment near the rear light unit, while for the front version it is located inside the passenger compartment under the dashboard.
EPS-DUAL 4.0 details with Wireless Display (rear)
EPS-FRONT 4.0 details (front)
Main features
EPS-DUAL 4.0
with Wireless Display (rear)
Range of action
70/80 cm. up to a few centimeters
Obstacles detected
all shapes and materials
Sensitivity adjustment
4 pre-set sensitivities
Diet
connection to the reversing lamp
Activation
when engaging reverse gear
Antenna sensor length
3.5 meters (can be cut to the length of the bumper)
Display power cable length
40 cm
Data cable length
1.5 meters
Compatible with CAN BUS and CHECK CONTROL
No interference with other on-board equipment
Antenna sensor installation
internal bumper
Display
multicolored led bar and built-in buzzer, Wireless
Wireless Display (rear)
Multicolored led bar display
Built-in buzzer
Wireless
Alimentation cable:
2.0 meters
TO:
10 cm
B:
2 cm
Depth:
1.5 cm
Color:
black
Incompatible vehicles (rear)
The following vehicles are NOT compatible with the EPS-DUAL 4.0 parking sensor with Wireless Display:
Mazda Pickup | Mitsubishi L200 | Nissan Patrol (with metal bumper) | Nissan Pathfinder (version with spare wheel on the tailgate) | Nissan Navara | Toyota Rav 4 (before 2006) | Audi A4 (2006) | Fiat Doblò (pre 2010) | Isuzu D-Max | VW T5 California | volkswagen amarok | Nissan Primastar | Jeep Cherokee (version with spare wheel on the tailgate) | Jeep Wrangler | Peugeot Partner Tepee | Mitsubishi Pajero | Mercedes ML 2002 | VW Caddy | Hyundai H1 | Suzuki Splash (2014) | Fiat Ducato | Fiat Fullback | Land Rover Discovery 2 | Land Rover Defender | Mercedes Vito | Range Rover 1999 | Renault Trafic | Toyota Hilux | Mercedes Citan |
Tips for the Audi A4 and Audi A6 (4f) (rear):
On some versions of Audi A4 and Audi A6 (4f) it is not possible to install the standard antenna sensor supplied with the EPS-DUAL 4.0 model with Wireless Display but a specific antenna sensor must be used (
details
). You can request this type of antenna sensor indicating it in the notes before sending the order.
Assembly instructions (rear)
Assembly instructions in Italian rear parking sensor mod. EPS-DUAL 4.0 with Wireless DISPLAY
Main features
EPS-FRONT 4.0
(front)
Range of action
from 60/70 cm. up to a few centimeters
Obstacles detected
all shapes and materials
Sensitivity adjustment
4 pre-set sensitivities
Diet
connection to the car battery
Activation
via button
Antenna sensor length
3.5 meters (can be cut to the length of the bumper)
Buzzer-button cable length
1.0 meters
DATA cable length
2.5 meters
Compatible with CAN BUS and CHECK CONTROL
No interference with other on-board equipment
Antenna sensor installation
internal bumper
Incompatible vehicles
EPS-FRONT 4.0
(front)
The following vehicles are NOT compatible with the EPS-FRONT 4.0 parking sensor:
- Jeep Wrangler
- BMW Z4 (2007)
- Land Rover Defender
- Range Rover (1999)
Assembly instructions
EPS-FRONT 4.0
(front)
Assembly instructions in Italian front parking sensor  mod. EPS-FRONT 4.0
Antenna sensor
Unlike classic "button" sensors, electromagnetic parking sensors use a single sensor that is applied inside the bumper.
The
antenna sensor is aluminum tape
1 cm high, 3.5 meters long and a few tenths thick.
Once applied from one end of the bumper to the other, the excess can be cut off.
Details
Where to install the antenna sensor on your car:
We suggest the
positioning of the antenna sensor
inside the bumper. If your car is not listed on the
our site
report it to us
mail
indicating the model and year of registration.
By purchasing this product on our site you will be entitled to:
3 year guarantee
Technical assistance from the manufacturer
Italian product
More information
For more information and technical characteristics visit the
our site